テクトロニクス担当者とライブ・チャット： 午前9時～午後5時00分 JST
NTSC Signal Generator
Features & Benefits
- NTSC Test Signals
- Multiple Black Burst Outputs
- Character Identification Positionable Within the Active Field
- Tape Leader Countdown with Visual and Audio Cues
- Stereo Audio Tone with Channel One Identification
- 12 V DC Input
- Remote Control
- Small Production System SPG
- Color Bars/ID Source for Microwave Links
NTSC Test Signals
The TSG200 provides six NTSC test signals. These 10-Bit signals provide for both studio production and first line maintenance. The signal set is:
- SMPTE color bars
- NTC 7 composite
- 5-step staircase
- Black burst
Multiple Black Bursts
For driving small production systems, the TSG200 provides multiple black burst outputs. It is configurable to provide either two test signal outputs and four black bursts, or one test signal output and five full time black bursts.
ID and Countdown
The TSG200 has two lines of ID text that can be positioned vertically anywhere on the active field. The first line of this ID can also be located in the vertical interval. Eight ID captions can be stored and recalled at the front panel or via the remote control. Up to four captions may be cycled in sequence, with each displayed for approximately four seconds.
The tape leader countdown provides an accompanying audio tone pulse that is synchronous with the countdown.
For automatic identification, the TSG200 generates a "source ID" pulse code on line 16 of the vertical interval. The Tektronix VM700A Video Measurement Set uses this code for identification of sources on displays and printouts of measurement routines. The code is internally selectable and may be enabled and disabled from the front panel.
Audio Tone with Channel ID
For continuity checks and level testing, the TSG200 offers a phase locked, two channel, 1 kHz audio tone. An adjustable rate identification pulse is provided on channel one.
Ground closure remote control is provided for the following functions:
- Test signal select
- Character identification enable
- Initiate tape leader countdown
- Source identification enable
- Channel one audio tone identification enable
- Character identification preset recall
- Sequence identification presets
- Front panel disable
NTSC Signal Generator
Luminance Amplitude Accuracy - ±1%.
Chrominance-to-luminance Gain - ±1%.
Chrominance-to-luminance Delay - ≤12 ns.
Frequency Response - ±2% to 4.2 MHz.
SCH Phase Accuracy - 0° ± 5°.
Line Blanking Interval - 10.9 µs ±0.2 µs.
Output Impedance - 75 Ω.
NTSC Test Signals
Color Bars - SMPTE Color Bars.
Convergence - 14 lines per field 17 lines per horizontal.
White reference bar amplitude: 70 IRE.
Packet amplitudes: 60 IRE.
Pedestal: 40 IRE.
Burst frequencies: 0.5, 1.0, 2.0, 3.0, 3.58 and 4.2 MHz.
5-step Staircase -
Amplitude: 100 IRE.
Linearity error: ≤1%.
NTC 7 Composite -
Blanking width: 10.9 µs ± 0.2 µs.
Frequency - 3.579545 MHz.
Audio Tone Generator
Frequency - 1 kHz or 400 Hz.
Amplitude - 0 to +8 dBu into 600 Ω, or a high impedance load.
Distortion - ≤0.5% THD.
Click ID - Rate adjustable from 0.2 Hz to 4 Hz.
Mains Voltage Range - 90-130 VAC; 180-250 VAC.
Frequency Range - 48-62 Hz.
Power Consumption - 15 W typical.
Operating: 0 °C to 35 °C.
Nonoperating: 40 °C to 65 °C.
Safety - Approved to: UL1244, CSA231.
Optional Mounting Kits
TVGF11A - Hardware to mount any one of TSG100 Series, ASG100 or VITS100 products in a one-rack unit high space.
TVGF13 - Hardware to mount any two of TSG100 Series, ASG100 and VITS100 products side-by-side in a two-rack unit high space.
TVGF14 - Hardware to mount any two of TSG100 Series, ASG100 and VITS100 products vertically in one-half of a WFM7F05 rack adapter.
Opt. C3 - Calibration Service 3 Years
Opt. C5 - Calibration Service 5 Years
Opt. D1 - Calibration Data Report
Opt. D3 - Calibration Data Report 3 Years (with Option C3)
Opt. D5 - Calibration Data Report 5 Years (with Option C5)
Opt. R3 - Repair Service 3 Years
Opt. R5 - Repair Service 5 Years